喜歡這套資料就充值下載吧。。。資源目錄里展示的都可在線預覽哦。。。下載后都有，，請放心下載，，文件全都包含在內，，【有疑問咨詢QQ:1064457796 或 1304139763】
摘要
國產壓磚機的技術參數、技術性能等己達到或部分超過國外先進壓磚機的水平，但液壓系統的設計主要借助于經驗，而理論上的研究工作較少。因此，對自動壓磚機的液壓系統理論基礎僅進行研究，為改進、優化液壓系統，提高壓制次數，縮短循環時間，提升壓磚機的產能提供理論支持有一定的積極意義。本文主要任務就是了解液壓壓磚機的整體結構，對液壓機本體結構的主要部件進行強度核算，保證機器的運行安全。同時根據壓力和流量這兩個液壓系統的主要參數來選擇液壓元件、輔件和原動機的規格。最后對液壓機的技術性能進行估算，以便從幾種設計方案中比較出最佳方案，或判斷其設計質量。本文中進行了：系統壓力損失計算，系統效率計算，系統發熱與溫升計算，液壓沖擊計算等。
關鍵詞：壓磚機；本體結構；優化設計
Abstract
The design and manufacturing level of hydraulic automation tile press has taken remarkable achievement not only by introduction, duplication and digestion of oversea advanced equipment, but also by independent manufacturing of hydraulic automation tile press with knowledge authorization. Although the technological parameters and functions of domestic hydraulic automation tile press has been gained or exceeded partly oversea advanced technological level of hydraulic automation tile press, design on the hydraulic system is based on working experience with less theoretic research. Therefore, it is positive to do theoretic base research on hydraulic system to improve, optimize hydraulic system, shorten cycle time and increase production. Learn the whole construction of the hydraulic jewel press machine, and figure up the strength of the main components to ensure its safe running.?Pressure and flow capacity are the main parameter of hydraulic system, according to which we can calculate and choose the specifications of elements, auxiliaries and the prime motor. And last,estimate the technical data of hydraulic press to cull a best one from the several designed plans, or to judge its quality.? This paper contains: calculations of system pressure, system efficiency, system heat emitting and temperature raising, hydraulic shock and so on.?
key words: brick press noumenon configuration optimum design
徐州工程學院畢業設計
目錄
1 緒論…………………………………………………………………………………………..1
1.1液壓壓磚機的現狀與發展趨勢…………………………………………………………..1
1.1.1國內液壓壓磚機的現狀與發展趨勢………………………………………………….1
1.1.2國外液壓壓磚機的現狀與發展趨勢………………………………………………….2
2 設計計算的內容和步驟……………………………………………………………………..4
3 液壓機本體結構及設計計算………………………………………………………………..5
3.1液壓壓磚機液壓系統的組成及功能……………………………………………………..5
3.2液壓壓磚機的液壓回路…………………………………………………………………..5
3.3本體結構的選擇…………………………………………………………………………..5
3.4立柱的強度計算…………………………………………………………………………..6
3.5橫粱的強度與剛度計算…………………………………………………………………..7
4 確定液壓系統的主要參數…………………………………………………………………..11
4.1 初選系統壓力…………………………………………………………………………….11
4.2 計算液壓缸主要尺寸及其選擇………………………………………………………….11
4.3 計算液壓馬達排量……………………………………………………………………….15
4.4 計算液壓缸或液壓馬達流量…………………………………………………………….16
4.4.1液壓缸的最大流量…………………………………………………………………….16
4.4.2 液壓馬達的最大流量…………………………………………………………………16
4.5 液壓馬達的選用………………………………………………………………………….17
5 擬訂液壓系統圖……………………………………………………………………………..18
5.1 確定和選擇基本回路…………………………………………………………………….18
5.2 調速方式的選擇………………………………………………………………………….18
5.3 油路循環形式的選擇…………………………………………………………………….19
5.4 需要綜合考慮的其他問題……………………………………………………………….19
6 液壓元件的選用……………………………………………………………………………...21
6.1 液壓泵的選擇……………………………………………………………………………..21
6.1.1 確定液壓泵的工作壓力……………………………………………………………….23
6.1.2 確定液壓泵的流量…………………………………………………………………….23
6.1.3 選擇液壓泵的規格…………………………………………………………………….24
6.1.4 確定驅動液壓泵的功率……………………………………………………………….24
6.2 控制閥的選擇…………………………………………………………………………….26
6.2.1 壓力控制閥的選擇原則……………………………………………………………….26
6.2.2 流量控制閥的選擇…………………………………………………………………….26
6.2.3 方向控制閥的選擇…………………………………………………………………….26
6.3 蓄能器的選擇…………………………………………………………………………….28
6.4 管道種類的選擇………………………………………………………………………….28
6.4.1 管道內徑的確定……………………………………………………………………….29
6.4.2管道壁厚的確定………………………………………………………………………..30
6.4.3 管接頭的選擇………………………………………………………………………….31
6.5確定油箱容量……………………………………………………………………………..31
6.6 過濾器的選用…………………………………………………………………………….32
6.7 液壓油的選用…………………………………………………………………………….33
7 液壓系統性能估算…………………………………………………………………………...35
7.1 系統壓力損失計算………………………………………………………………………..35
7.2 系統效率估算……………………………………………………………………………..36
7.3 液壓沖擊估算……………………………………………………………………………..37
8 壓制油缸優化設計…………………………………………………………………………...39
8.1前言………………………………………………………………………………………...39
8.2單層厚壁油缸的應力和應變分析………………………………………………………...39
8.3薄壁油缸的應力和應變分析……………………………………………………………...41
8.3.1油缸壓力為零時，薄壁油缸的應力和應變…………………………………………..42
8.3.2油缸應力為P時，薄壁油缸的應力和應變…………………………………………..43
8.4薄壁油缸的優化設計……………………………………………………………………...44
8.4.1優化目標的提出………………………………………………………………………..44
8.5總結………………………………………………………………………………………...45
結論……………………………………………………………………………………………...46
致謝……………………………………………………………………………………………...47
參考文獻………………………………………………………………………………………...48
附錄……………………………………………………………………………………………...49
附錄1………………………………………………………………………………………..49
附錄2……………………………………………………………………………………….58
- 3 -