球面零件專用切削機床設計[機+電]

喜歡這套資料就充值下載吧。資源目錄里展示的都可在線預覽哦。下載后都有，請放心下載，文件全都包含在內，圖紙為CAD格式可編輯，有疑問咨詢QQ:414951605 或 1304139763p 沈陽理工大學學士學位論文 摘 要 我這次畢業設計的題目是球面切削專用設備。該專用設備的設計方案主要依據仿形車削的工作原理。其中包括床頭箱的設計和進給機構的設計。床頭箱要滿足4級變速，并能在更換工件時迅速制動。進給機構包括縱向進給液壓缸、橫向進給液壓缸，曲柄滑塊機構和型槽。 車刀的縱、橫兩方向移動均采用液壓驅動，因此液壓系統的設計是否合理直接影響到機床的工作性能。在液壓系統中，床鞍及滑塊的運動方向分別由各自的三位四通電磁換向閥控制，其運動速度由安裝在各自油缸回油路上的調速閥及二位二通電磁換向閥聯合控制。由溢流閥調整系統油壓，調整后的數值可由壓力表測出。 該設備的電氣部分采用PLC控制。它可靠性高，抗干擾能力強，結構簡單，功耗低，并由實際情況考慮，決定采用F1三菱系列PLC。 一個好的專用設備應該達到：1）提高生產率和工人勞動生產率，顯著減輕工人勞動強.2）工作穩定可靠，使用壽命長。3）易于維修，成本低。根據理論驗證，上述方案基本達到要求。 關鍵詞: 仿形車床；液壓系統；PLC Abstract The topic of this graduation project of mine is that the sphere cuts the dedicated device . Operation principle of main basis profile modelling turning of design plan of this dedicated device . Include the design of the bedside case and enter to the design of the organization. The bedside case wants satisfied 4 grades to change speed, and can apply the brake rapidly while changing the work piece . Enter to the organization including getting vertical, trough of slippery organizations of crank and type. The vertical , two horizontal directions of the lathe tool move and adopt the hydraulic pressure to urge , so the design systematic in hydraulic pressure influences the working performance of the lathe directly rationally. Among hydraulic pressure system, bed saddle slip sport direction of piece control by one's own 3 electromagnetic reversing valve of Stone separately, sport its speed install in each cylinder going back to transfer speed valve and 2 electromagnetic reversing valves 2 times jointly control oil passaging. Is it flow valve adjust systematic oil pressure , adjust number value after can be measured by the manometer to overflow. A fine dedicated device should reach : 1)Boost productivity and worker labor productivity, lighten worker work strong notably. 2)It is reliable that the work is steady, have long performance life. 3)Easy to maintain, with low costs. Verify according to theory above-mentioned schemes reach demanding basically. Keyword: copying lathe ； hydraulic pressure system ；PLC II