522 履帶拖拉機無級變速器設計（行星機構設計）（有cad圖）

522 履帶拖拉機無級變速器設計（行星機構設計）（有cad圖）,522,履帶拖拉機無級變速器設計（行星機構設計）（有cad圖）,履帶,拖拉機,無級,變速器,設計,行星,機構,cad 履帶拖拉機無級變速器設計（行星機構設計） 摘 要 目前國際上大功率履帶拖拉機以及部分工程車輛的傳動系廣泛采用液力變矩器與動力換檔變速箱組合形式，即動力機械傳動。還有部分先進機型采用了全液壓傳動技術，其操縱已由手動電液控制或微電腦控制技術方面發展，并取得非常好的效果，大大提高了整機行駛平順和作業性能，雖然他們都具有無級變速的功能，操縱輕便，整機動力性好，可靠性高，但由于傳動系的傳動效率較低，直接影響了整機生產率和經濟性。 液壓機械無級變速器是綜合了機械傳動高效率和液壓傳動無級變速兩方面優點的新型傳動機構。液壓機械無級傳動是一種多流傳動系統，它將功率分為液壓和機械兩路傳遞，分流機構分流后液壓馬達在正向和反向最大速度之間來回無級變速。其每一個行程和行星齒輪機構的一種工況相配合，最兩路匯合成由若干無級調速段相銜接并組逐段升高的全程無級變化輸出速度。和液力機械傳動相比，裝載量最大可提高30%，燃油經濟性最大可提高25%。 此設計主要是針對行星齒輪機構以及控制部分離合器的設計。對于行星齒輪采用單排的結構形式，這樣可以減小整個無級變速器的軸向尺寸，但是為了能夠承受較大的和變化的載荷，于是在中心輪的周圍均勻地分布著數個行星輪來共同分擔載荷。本設計采用3個行星論均勻的布置形式就可以達到要求。其控制部分采用多片的用壓力油控制的濕式離合器。離合器隨著載荷的增加可以增多摩擦片的對數或增加其徑向尺寸。在設計的過程中這兩方面是綜合考慮的，因為不可能使軸向或徑向的尺寸過分的偏大。 關鍵詞：拖拉機，液壓機械傳動，無級變速器，行星排 DESIGN OF CONTINUOSLY VARIABLE TRANSMISSION OF TRACKED TRACTOR（PLANETARY GEARS DESIGN）　 ABSTRACT At present, international large crawler tractors, as well as some works vehicles widely used transmission torque converter with variable power shift speed box combinations, which is the power mechanical drive. There are also some advanced models use a hydraulic transmission technology, which has been manually manipulated its electro-hydraulic control or microcomputer control technology development, and achieved very good results, greatly enhance the overall ride comfort and operational performance, although they have CVT function, manipulating light, whole dynamic, and high reliability, but because the transmission system drive less efficient direct impact on the overall productivity and economy. Hydraulic machinery CVT is a synthesis of highly efficient mechanical transmission and hydraulic drive CVT merits of the two new motivation - structure. Hydro-Mechanical - drive is a multi-stream transmission, power will be divided into two hydraulic and mechanical transmission path, streaming agencies triaged hydraulic motor in forward and reverse maximum speed between both CVT. Each of its itinerary and a planetary gear mechanism for a state match, most roads converge into two by a number of variable speed converge and the group has to absolutely no higher level of output speed changes. Hydraulic and mechanical transmission, the loading capacity can be increased by 30%, fuel economy can be increased 25%. This design is mainly directed against planetary gear mechanism and the control of the clutch part of the design. For single planetary gear arrangement of the structure, thus reducing the entire CVT axial dimensions, however, in order to be able to make and take greater changes in the load, So in the center of the round around evenly distributed several planetary gear to load shared. The three designs on the planet uniform layout can meet the requirements. Clutch with load increasing friction can increase the number of tablets or increase its radial dimension. In the process of designing these two aspects are considered, as it is impossible to make radial or axial dimensions excessive. Key words：tractor，hydro-mechanical transmission，continuously variable transmission, planetary gears 符 號 說 明 K 載荷系數 D 摩擦片的外徑 d 摩擦片的內徑 B 儲備系數 q 摩擦片的單位壓力Mpa R 摩擦片的平均作用半徑m F 摩擦面的平均作用面積 每個摩擦副扣除溝槽后的凈面積 摩擦片上的總壓力N 摩擦系數 花鍵軸的摩擦系數 摩擦片的對數 壓力損失系數 旋轉油缸的轉速 旋轉軸的外徑 排油需要的壓力Mpa q 油缸的工作壓力Mpa 密封圈的摩擦阻力N 壓力損失對活塞的阻力N 離心力對活塞的阻力N 回位彈簧力N 最小工作載荷是 彈簧的剛度 最小工作下的變形量 最大工作下的變形量 最小切應力 最大切應力 目 錄 第一章 緒論......................................1 §1.1 液壓機械無級變速器研究的意義....................1 §1.2 液壓機械無級變速器的傳動原理....................1 §1.3 此設計的研究重點................................2 第二章 行星齒輪的設計與計算.........................4 §2.1行星齒輪的特點分析..............................4 §2.2行星齒輪的尺寸計算..............................6 第三章 離合器的設計與計算...........................9 §3.1 離合器的特點分析................................9 §3.1.1 摩擦離合器的作用........................... 9 §3.1.2 濕式摩擦離合器的設計要點...................10 §3.2 離合器的計算............................... .11 §3.2.1 離合器的尺寸計算.........................11 §3.2.2 離合器的彈簧計算.........................12 §3.3 離合器計算...................................15 §3.3.1 離合器的尺寸計算.........................15 §3.3.2 離合器的彈簧計算.........................16 §3.4 離合器的計算.................................19 §3.4.1 離合器的尺寸計算.........................19 §3.4.2 離合器的彈簧計算.........................20 §3.5 離合器的計算.................................23 §3.5.1 離合器的尺寸計算.........................23 §3.5.2 離合器的彈簧計算.........................24 第四章 結論...........................................28 參考文獻...............................................29 致謝...................................................31 V