裝配圖管磨機的總體和結構設計

裝配圖管磨機的總體和結構設計,裝配,圖管磨機,總體,整體,以及,結構設計 管磨機動態特性及系統的測試分析 學生姓名：張攀程 班級：0781053 指導老師：張曉榮 摘要：磨機是發電、選礦、化工和建材等重工業領域中最廣泛采用的粉磨機械，其主要機件有傳動裝置、支承裝置、回轉筒體。 本文建立了邊緣傳動式磨機系統的“小齒輪——傳動軸——減速機大齒輪”橫向振動的模型，分析計算了系統橫向振動的動態特性，對系統的載荷進行了測試分析，同時，還建立了磨機系統的扭轉振動模型，利用遞推計算法對系統進行了扭轉振動動態特性分析，驗證了遞推計算法的通用性。最后，對Φ2.6×13m的磨機系統進行了動態特性的實例分析。 研究邊緣傳動磨機系統的動態特性，對避免由于激勵頻率接近或等于系統的固有頻率而導致共振及設備的失效，預測系統在可能激勵下的響應特性，優化系統結構等等都具有很重要的意義。 用傳遞矩陣法及通用計算程序可以簡便地分析邊緣傳動磨機系統橫向振動的固有特性，以及計算不同激勵情況下系統的響應，為研究邊緣傳動磨機系統橫向振動的動態特性提供了一個方便有效的方法。 邊緣傳動磨機系統是一個模態偶合較緊的系統，因此，在磨機系統的設計、運行中，應注意使激勵頻率避開系統的固有頻率，以免發生設備的早期失效。 邊緣傳動式磨機系統的傳動軸的設計是合理的。 系統阻尼對系統的動態特性影響很大，是系統的一個重要性能參數。 邊緣傳動磨機系統，可以通過實測低速軸的扭矩來確定系統中減速機的負載狀況。 關鍵詞：振動 載荷 響應特性 扭矩 指導老師簽名： Tube Mill and testing of the system Dynamic Analysis Student name：Zhang PanCheng Class：0781053 Supervisor：Zhang XiaoRong Abstract：Tube Mill is important rules that Research for Dynamic characteristics of the mill system of single -pinion drives in operation to prevent damage from the resonance between fix frequency and bestir frequency In this paper , the pattern of Pinion---Drive shaft---Decelerator gear vertical vibration in the mill system of single -pinion drives is established . Dynamic characteristics of vertical vibration is analyzed and calculated ,and its excitation loads are tested Simultaneously , the model of torsion vibration in system is also established, its dynamic characteristics is analyzed by using recurrence calculus method , thus , this methods current is verified . Finally, the paper studied the dynamic characteristics of 2.6x13m mill system. Mill system of single - pinion drives is lighten, so the design and run of mill system, bestir frequency must avoid inhesion.The design of drive shaft is rational in mill system of single - pinion drives. It is very large that damp of system effect to dynamic characteristics, so the damp is a important parameter. Load of gear box can be decided by measuring of low speed shaft contort. In mill system of single - pinion drives. Key words：vibration response characteristics load torque Signature of Supervisor： 南昌航空大學科技學院2011屆學士學位論文