購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。。【注】：dwg后綴為CAD圖，doc,docx為WORD文檔，有不明白之處，可咨詢QQ:1304139763
礦 泉 水 瓶 蓋 注 塑 模 設 計 摘要 本設計題目為礦泉水瓶蓋注塑模設計 體現了殼體類塑料零件的設計要求 內容及方向 有一定的設計意義 通過對該零件模具的設計 進一步加強了設計者注 塑模設計的基礎知識 為設計更復雜的注塑模具做好了鋪墊和吸取了更深刻的經驗 本設計運用塑料成型工藝及模具設計的基礎知識 首先分析了塑件的成分及性能 要求 為選取澆口的類型做好了準備 然后估算了塑件的體積 便于選取注塑機 最 后分析了塑件的特征 確定模具的設計參數 設計要點及推出裝置的選取 本塑件屬于殼體類零件 同時內側有一個螺紋 因此設計時必須考慮螺紋塑件的 脫模 本設計采用螺紋塑件的旋轉脫模 所以采用自動脫模機構 關鍵詞 注塑模 澆口 型芯 脫模機構 injection mold design for the mineralwater bottle cover Abstract This design topic notes an injection mold design for the mineral water bottle cover body now the hull body plastics design request contents and direction of the spare parts there is certain design meaning Pass the design to the spare parts molding tool strengthenned a design to note the injection mold foundation knowledge of design further for design to more complicatedly note a injection molding tool to have done cushion and absorb deeper experience This design usage plastics models the foundation knowledge of craft and molding tool design composition and function which analyzed a injection piece first request sprinkle an oscular type to have done preparation for the selection Then estimated the physical volume of injection piece the easy to selection noted injection machine Finally analyzed the characteristic of injection piece make sure the design parameter design important point of molding tool and release the selection of device This injection piece belongs to the hull body spare parts the seamy side contains a thread in the meantime so design have to consider the thread injection take off of piece a mold This design adoption thread injection revolve of piece takes off a mold and have because of the inner part turn of hollow type Xin so the adoption moves to take off automatically take off mold organization Keyword The injection mold sprinkle Core Take off mold organization