輪轂加工工藝規程及專用車夾具設計（全套帶CAD圖紙）

輪轂加工工藝規程及專用車夾具設計（全套帶CAD圖紙）,輪轂,加工,工藝,規程,專用車,夾具,設計,全套,cad,圖紙 摘 要 本次畢業設計的題目是輪轂加工工藝規程及專用車夾具設計。我主要需要完成的包括加工工藝的安排以及專用機床夾具設計。為了保證加工零件的精度同時節約成本和縮短加工周期以及提高加工效率，那么一個良好的工藝安排以及專用夾具的設計就是必不可少的了。在工藝的安排上不但要考慮合理的加工要求還要考慮到操作者以及加工機械的安全。同時夾具的設計上也要考慮到使用的安全性和經濟性以及安裝和拆卸上的方便性。設計一個良好的工藝工裝安排路線那么必須要經過對加工件的詳細分析以及周密的考慮后才能得出。所以分析問題是解決問題的關鍵，同時還要反復的調整，來尋求最好的一個路線。這樣才能讓工藝路線更加的完美，才能保證工件的加工精度和加工效率以及節約材料。 關鍵詞：工藝，工序，切削用量，夾緊，定位，誤差 Abstract This graduation design topic is the wheel hub processing craft specification and the special-purpose vehicle jig design. I mainly need to complete the processing technology and special machine tool fixture design. In order to ensure machining precision at the same time, save cost and shorten the processing cycle and improve the processing efficiency, then a good process arrangement and special fixture design is essential for the. In the process of the arrangement not only to consider the reasonable processing requirements but also taking into account the safety of the operator and processing machinery. At the same time, the design of the fixture should take into account the use of safety and economy as well as the ease of installation and disassembly. To design a good process for the arrangement of the route then must go through a detailed analysis of the processing parts and careful consideration before the. So the problem is to solve the problem is the key to solve the problem, but also to repeatedly adjust, to seek the best route. In order to make the process more perfect, to guarantee the processing accuracy and efficiency of the workpiece and save materials. Keywords: process, process, cutting dosage, clamping, positioning 目 錄 摘 要 II 目 錄 III 第1章 序 言 5 第2章 零件的分析 6 2.1零件的形狀 6 2.2零件的工藝分析 6 第3章 工藝規程設計 7 3.1 確定毛坯的制造形式 7 3.2 基面的選擇 7 3.3 制定工藝路線 8 3.3.1 工藝路線方案一 8 3.3.2 工藝路線方案二 8 3.3.3 工藝方案的比較與分析 9 3.4 選擇加工設備和工藝裝備 10 3.4.1 機床選用 10 3.4.2 選擇刀具 10 3.4.3 選擇量具 10 3.5 機械加工余量、工序尺寸及毛坯尺寸的確定 10 3.6確定切削用量及基本工時 12 第四章 車床夾具設計 20 4.1 車床夾具設計要求說明 20 4.2車床夾具的設計要點 20 4.3 定位機構 22 4.4夾緊機構 22 4.5零件的車床夾具的加工誤差分析 23 4.6 確定夾具體結構尺寸和總體結構 23 4.7 零件的車床專用夾具簡單使用說明 24 總 結 26 致 謝 27 參 考 文 獻 28