雷達說明書2117

《雷達說明書2117》由會員分享，可在線閱讀，更多相關《雷達說明書2117（144頁珍藏版）》請?jiān)谘b配圖網上搜索。

1、1 RADAR OPERATION 雷達操作 1.1 Turning on the Power 開啟雷達 The [POWER] switch is located at the left corner of the control unit. Open the power switch cover and press the switch to turn on the radar system. To turn off the radar, press the switch again. The screen shows the bearing scale and d

2、igital timer approximately 30 seconds after power-on. The timer counts down three minutes of warm-up time. During this period the magnetron (transmitter tube) is warmed for transmission. When the timer has reached 0:00, the indication "ST-BY" appears at the screen center, meaning the radar is now re

3、ady to transmit pulses. 電源鍵位于控制面板的左上角。打開電源蓋、按下打開電源。再次按下關閉電源。電源開啟后30秒屏幕顯示方位圈、電子計數器，計數器倒計時3分鐘磁控管預熱時間。但計數器時間歸零，屏幕中央顯示“待機”，表示雷達已準備發射。 In the stand-by condition, markers, rings, map, charts, etc. are not shown. Further, ARP is cancelled and the AIS display is erased. 在待機的情況下，標志、距標圈、海圖等將不顯示。ARPA功能取消，AI

4、S顯示取消。 In warm-up and stand-by condition, ON TIME and TX TIME counts in hours and tenths of hour appear at the screen center. 在預熱和待機的情況下，使用時間和發射時間鍵顯示在屏幕中間（*.*H）。 1.2 Transmitter ON 啟動發射機 After the power is turned on and the magnetron has warmed up, ST-BY appears at the screen center

5、, meaning the radar is ready to transmit radar pulses. You may transmit by pressing the [STBY/TX] key on the full keyboard or roll the trackball to choose the TX STBY box at the bottom left corner of the display and then push the left button (above the trackball). The label at the left-hand side of

6、the guidance box at the bottom right corner of the screen changes from TX to STBY 在電源打開、磁控管預熱后，ST-BY顯示在屏幕中間，表示已準備發射。按準備鍵或用鼠標選擇屏幕左下角的發射準備框打開雷達 。 雷達顯示 The radar is initially set to previously used range and pulse length. Other settings such as brilliance levels

7、, VRMs, EBLs and menu option selections are also set to previous settings. 雷達的設定（量程、脈沖長度、亮度、活動距標圈、電子方位線、菜單選項等）為上次關機時的設定。 The [STBY/TX] key (orTX STBY box) toggles the radar between STBY and TRANSMIT status. The antenna stops in stand-by and rotates in transmit. The magnetron ages with time resulti

8、ng in a reduction of output power. Therefore, it is highly recommended that the radar be set to stand-by when not used for an extended period of time. ST-BY/鍵聯系雷達待機和發射兩種狀態。待機狀態下天線不轉動、在發射狀態下轉動，磁控管的使用時間影響輸出功率的大小，因此前來建議在雷達長時間不使用的情況下鍵雷達設于待機狀態。 Quick start 快速啟動 Provided that the radar was once in use

9、 with the transmitter tube (magnetron) still warm, you can turn the radar into TRANSMIT condition without three minutes of warm-up. If the [POWER] switch has been turned off by mistake or the like and you wish to restart the radar promptly, turn on the [POWER] switch not later than 10 seconds after

10、power-off. 如果雷達仍在使用，磁控管仍然預熱，可以無需等待3分鐘。如果誤關機，又馬上要開機，請?jiān)?0秒內馬上打開電源。 1.3 Control Unit 控制單元 Two types of control units are available: Control Unit RCU-014 (full keyboard) and Control Unit RCU-105 (palm control). 本雷達提供兩種控制單元，RCU-014型鍵盤式、RCU-105型手掌式。 Control description 控鍵 Contro l控鍵

11、 Description 功能描述 Control Unit RCU-014 (full keyboard) RCU-014型鍵盤式 POWER 電源 Turns the system on and off. 開關電源 EBL and VRM rotary controls 電子方位線、活動距標圈轉盤 Adjust EBL and VRM, respectively. 調節電子方位線、活動距標圈 EBLON, EBL OFF 電子方位線開關 Turns the EBLs on and off, respectively. 開關電子方位線 F1-F4 功能

12、鍵 Execute menu short cut assigned .快捷鍵 ALARM ACK 警報確認 Silences audible alarm. 關閉聲響警報 STBY/ TX 待機/發射鍵 Toggles between stand-by and transmit. 待機或發射 BRILL 亮度 Adjusts display brilliance .調節顯示亮度 A/C RAIN 雨雪抑制 Suppresses rain clutter. 抑制雨雪雜波 A/C SEA 海浪抑制 Suppress

13、es sea clutter .抑制海浪雜波 GAIN 增益 Adjusts sensitivity of the radar receiver. 調節雷達接收機靈敏度 HLOFF 船首線關閉 Temporarily erases the heading line while pressed. 臨時消除船首線（按住） EBL OFFSET 電子方位線偏心顯示 Enables, disables the EBL offset. In menu operation, switches polarity from North to South and Ea

14、st to West and vice versa. 開啟關閉電子方位線偏心顯示，菜單操作時選擇南或北、東或西 MODE 顯示模式 Chooses presentation mode。 選擇顯示模式 OFF CENTER 偏心顯示 Shifts own ship position. 調整本船位置 CU/TM RESET 真運動、航向向上顯示復位 Moves own ship position in 75% radius in stern direction. ? Resets the heading line to 0 in course-up and

15、true motion modes. 真運動、航向向上時，船首線復位至零、本船至船尾方向半徑75%處， INDEX LINE 索引線 Turns index lines on and off. 開關索引線 VECTOR TIME 矢量時間 Chooses vector time (length). 調節矢量長度 VECTOR MODE 矢量模式 Chooses vector mode, relative or true. 選擇真矢量或相對矢量 TARGET LIST 目標列表 Displays ARP target list.

16、顯示ARPA目 標列表 CANCEL TRAILS 取消尾跡 Cancels all target trails. In menu operation it clears line of data. 取消目標尾跡，菜單操作中清除數據線 ENTER MARK 插入標志 Enters marks; terminates keyboard input. 插入標志；終止鍵盤輸入 VRM ON, VRM OFF 活動距標圈開關 Turns the VRMs on and off, respectively 開啟或關閉活動距標圈 MENU 菜單 Open

17、s and closes the MAIN menu; closes other menus. 開關菜單 ACQ 捕捉 ? Acquires a target for ARP after choosing it with the trackball. ? Changes a sleeping AIS target to an activated one after choosing it with the trackball. 捕捉物標、激活睡眠狀態的AIS目標 RANGE 量程 Chooses radar range. 選擇量程 TARGET DATA

18、 物標數據 Displays target data for ARP or AIS target chosen with the trackball. 顯示ARPA或AIS目標數據 TARGET CANCEL 目標取消 Cancels tracking on ARP, AIS or reference target chosen with the trackball .清除ARPA或AIS目標 Control Unit RCU-015 (palm control) RCU-105型掌控式 POWER 電源 Turns the system on and off.

19、 開關雷達 F1-F4 功能鍵 Execute menu short cut assigned .快捷功能鍵 主菜單 [主菜單] 1、[回波] 2、[標志] 3、[警報] 4、[ARPA AIS] 5、[標繪] 6、[記憶卡] 7、[航行數據] 8、[航線及轉向點] 9、[自定義、測試] 回波相關選項 標志相關選項 設置警戒圈、設定警報 ARPA AIS相關功能 海圖及航跡功能 記憶卡功能 開關航行數據 設定航線及轉向點 自定義功能及系統測試 2. Press the

20、 numeral key corresponding to the menu you wish to open. For example, press the [2] key to open MARK menu. 按數字鍵打開相應的菜單，例如按2打開標志菜單； [標志] 1、 返回 2、 本船標志開關 3、 船尾標志開關 4、 索引線方位 相對/真 5、 索引線 1/2/3/6 6、 索引線 垂直/水平 8、 子方位線基線 對地穩定/首向穩定/真北穩定 9、 電子方位線 真方位/相對方位 0、 固定距標圈 開/關

21、 標志菜單 菜單操作中的實用技巧 1、 使用[CANCEL TRAILS]鍵清除數字?jǐn)?shù)據 2、 使用[2]鍵切換南或北、加或減、東或西 3. Press the numeral key corresponding to the item you wish to set. 按數字建設定相應的選項； 4. Consecutively press the same numeral key pressed at step 3 to choose ap

22、propriate option and then press the [ENTER MARK] key to register your selection. 連續按相同數字鍵按第三步之操作選擇選項，按[ENTER MARK]鍵確認選擇； 5. Press the [MENU] key to close the menu. 按[MENU]鍵關閉菜單。 Main menu operation by trackball 鼠標操作菜單 1. Roll the trackball to choose the MENU box at the right side of the sc

23、reen. The guidance box at the bottom right corner (see the illustration at the bottom of the next page for location) now reads "DISP MAIN MENU." 用鼠標選擇屏幕右邊的菜單框，屏幕右下角的引導框顯示“打開主菜單” 菜單框 主菜單 2、 Use the left button to display the MAIN menu. 按左鍵打開

24、主菜單 3. Roll the wheel to choose the menu you wish to open and then push the wheel or the left button. For example, choose the 2 [MARK] menu and then push the wheel or the left button. 用滾輪選擇所需的選項，按滾輪或按左鍵確定。例如選擇2按左鍵或按滾輪進入標志菜單； 〔標志〕 1．返回 2．本船標志 3．船尾標志 4．索引線方位 真 / 相對 5．索引線 1/2/3/6

25、 6．索引線摸式 垂直 / 水平 8．EBL偏心基準 對地穩定/艏向穩定/ 真北穩定 9．EBL游標方位 真 /相對 0．固定距標 OFF / ON 4. Roll the wheel to choose item desired and then push the wheel or the left button. 用滾輪選擇所需的選項，按滾輪或按左鍵確定； 5. Roll the wheel to choose option desired and t

26、hen push the wheel or the left button to register your selection. 用滾輪選擇所需的選項，按滾輪或按左鍵確定； 6. Push the right button to close the menu. (Several pushes may be necessary depending on the menu used.) 按右鍵推出（根據情況可能需要按多次右鍵才能退出）。 1.5 Operation Using the On-Screen Boxes 使用屏幕選擇框進行操作 All ra

27、dar functions can be accessed by using the trackball alone. This is done by choosing the appropriate on-screen box with the trackball and operating the trackball module to choose item and option. (See paragraph 1 -9 for location of all on-screen boxes.) On-screen boxes come in two varieties: Functio

28、n selection and function selection w/pop-up menu. On-screen boxes of the latter type have >" at the right side of their boxes, as in the MARK box shown below. 所有功能均可通過鼠標單獨完成，選擇適當?shù)钠聊还δ芸?，用鼠?biāo)選擇相應的選項（詳見1。9節）。屏幕功能框分為兩種：功能選擇和功能菜單打開。 后一種功能框如下例之標志框，在框體右邊右箭頭顯示，表示可以打開相應的菜單。 To operate the radar using on-scr

29、een boxes, do the following: 按如下步驟使用屏幕選擇框進行操作： 1. Roll the trackball to place the trackball marker inside the box desired. 將鼠標箭頭至于所需的功能框內； Note: The trackball marker changes its configuration according to its location. It is an arrow when placed outside the effective display and a cursor

30、(+) when inside the effective display. See the illustration on the next page for further details. 鼠標箭頭根據所在的位置改變其形狀，在雷達顯示范圍內顯示為十字，在菜單顯示區內顯示為箭頭。詳見下一頁之圖例。 For example, choose the MARK box, which is at the bottom left corner 例如，選擇在屏幕左下角的標志框。 上次選擇的標志類型及標志編號

31、 距本船的方位距離 標志框 When a box is correctly selected, its color changes from green to yellow (default colors) and the guidance box at the bottom right corner shows operational guidance. The operational guidance shows the fu

32、nction of the left and right buttons, with a diagonal line separating the information. For the MARK box, for example, the operational guidance is "MARK SELECT / MARK MENU." In this case you would push the left button to choose a mark or push the right button to open the MARK menu. 當一個功能框被選中后，其顏色由綠變

33、黃，右下角的引導框顯示操作引導，引導框顯示相應的左右鍵的功能，左右鍵功能由斜線分開，例如標志框，引導框顯示為“標志選擇/標志菜單”，表示左鍵可以選擇不同的標志，右鍵進入標志菜單。 Trackball marker location and guidance box indication 鼠標位置和引導框的提示 The trackball marker is either a cursor (+) or an arrow (\) depending on whether it is within or outside the display area, re

34、spectively. Further, the indication in the guidance box changes according to trackball marker location. 鼠標箭頭根據所在的位置改變其形狀，在雷達顯示范圍內顯示為十字，在菜單顯示區內顯示為箭頭。引導框的內容根據鼠標的位置不同顯示相應的信息。 引導框顯示“跳過/顯示菜單”，表示按左鍵鼠標箭頭跳至最近的一個功能框，右鍵打開菜單。 Trackball marker is out

35、 of effective display area (incl. text area) and not selecting a box: The trackball marker is an arrow 鼠標光標在雷達有效顯示范圍外（包括文本區域）顯示為箭頭。 To choose boxes successively, push the wheel when the guidance box reads as above. Then, the nearest box is selected and marked with the double-ended arrow and the gu

36、idance box reads 按下滾輪滾動可連續選擇功能框，鼠標箭頭變?yōu)殡p箭頭，移動就可選擇下一個最近的功能框。 "JUMP FORWARD / JUMP BACKWARD." Hit the left button to go to the box below or adjacent to the currently selected box or hit the right button to go to the box above or adjacent to the currently selected box. Continue pushing a button to cho

37、ose boxes successively. This is convenient for operation under heavy pitching and rolling. To cancel this feature, push the wheel when the guidance box reads as above. “躍前/躍后”：按左鍵進入下一個與當前功能框相鄰的功能框，連續按則連續向下選擇功能框，按右鍵相反。該功能便于在船舶縱搖橫搖嚴重時使用，再按滾輪取消該功能。 Trackball marker is within effective display area: T

38、he trackball marker is a cursor 在有效顯示范圍中：鼠標標志為十字 2. Push the left button (or roll the wheel depending on the box) until the desired option is displayed in the box. 按左鍵（滾動滾輪）直至所需的選項出現在框中。 Note: When you chose an on-screen boxs option by rolling the wheel, the box and its contents turn red. This

39、 simply indicates that the chosen setting is different from the currently active setting. To change the setting, push the wheel or the left button. If neither the wheel nor the left button is pushed within about 30 seconds after operating the wheel, the previous setting is automatically restored. 注

40、意：當用鼠標選中了屏幕上的一個功能框時，該框體和內容顯示為紅色，這簡單的表明所選的設定異于當前激活的設定，按左鍵或滾輪改變?cè)O(shè)定，如果不按左鍵或滾輪超過三十秒，自動恢復原先的設定。 3. The pop-up menu attached to the MARK box is the MARK menu. To open the menu, push the right button. The menu opens in the text area at the right side of the screen. 菜單連接在標志菜單中的標志框中。按右鍵打開主菜單，菜單打開在屏幕右邊的文本框中。

41、 Note: Any menu may be operated from the full keyboard or the trackball, or a combination of the two in case of Control Unit RCU-014. 注意：任何菜單可以用鍵盤或鼠標操作，或混合操作。 Note that in later sections only the procedure for menu operation by the trackball is given. 注意：在以后的章節中只提供鼠標的操作。 4. Roll the wheel to

42、choose item desired and then push the wheel or the left button. Selected item is initially shown in reverse video and changes to normal video and circumscribed when the wheel or the left button is pushed. 用滾輪選擇所需的選項，按滾輪或左鍵。當按下左鍵或滾輪所選的選項初始顯示為相反顏色然后變回正常并在周?chē)涌颉? 5. Roll the wheel to choose option de

43、sired and then push the wheel or the left button. Selected option is initially shown in reverse video and changes to normal video and circumscribed when the wheel or the left button is pushed. 用滾輪選擇所需的選項，按滾輪或左鍵。當按下左鍵或滾輪所選的選項初始顯示為相反顏色然后變回正常并在周?chē)涌颉? 6. Push the right button to close the menu. (On s

44、ome menus several presses of the right button are required to close the menu.) 按右鍵關閉菜單（在一些情況下需要多次按右鍵才能退出菜單）。 Cursor Menu 光標菜單 Functions which require the use of the cursor, such as EBL offset and zoom, may be activated directly from the guidance box or from the CURSOR menu, either method with th

45、e cursor inside the effective display area. Below is the procedure for choosing a cursor-related function from the CURSOR menu. In later sections only the procedure for selection from the guidance box is given. 需要鼠標完成的功能如電子方位線或變焦放大功能，也可直接在引導框或光標菜單中完成。以下是從光標菜單中選擇光標相關功能。在以后的章節中只提供引導框選擇步驟。 1. Roll

46、the trackball to place the cursor inside the effective display area. 滾動鼠標移至有效雷達顯示范圍內； 2. Roll the wheel to show "TARGET DATA & ACQ / CURSOR MENU" in the guidance box. 滾動鼠標，引導框顯示“物標數據&錄取/光標菜單”； 3. Push the right button to show the CURSOR menu. 按右鍵顯示光標菜單； [光標菜單] 2、↓ 目標數據&錄取/ 取消物標/

47、 捕捉/ 參考標志/ 電子方位線偏心/ 偏心顯示/ 變焦放大/ 標志刪除/ 海圖排列/ 8、↑ 4. Roll the wheel to choose "2" and then push the wheel or the left button. 滾動滾輪選擇2，按左鍵或滾輪； 5. Roll the wheel to choose function desired and then push the wheel or the left button. 滾動滾輪選擇所需的功能，按左鍵或滾輪確認； Note: For op

48、eration from the keyboard, you may press the [2] key to choose a function in top-to-bottom order or the [8] key to choose in reverse order. 注意：當使用鍵盤操作的時候，按鍵盤[2]鍵從上到下選擇或按[8]鍵相反操作。 Cursor Menu item 光標菜單選項 Description 內容描述 TARGET DATA & ACQ 物標數據&錄取 ARP: Acquires ARP target; displays data

49、for chosen ARP target AIS: Activates sleeping AIS target; display data for chosen AIS target. ARPA: 錄取目標；顯示所選目標數據 AIS: 激活睡眠狀態的AIS目標；顯示AIS數據 TARGET CANCEL 取消物標 ARP: Cancels tracking on chosen ARP target. AIS. Sleeps chosen AIS target. ARPA：取消所選目標 AIS：轉換目標進入睡眠狀態 ACQ 錄取 ARP Acquires chosen

50、echo. AIS: Activates chosen AIS target. ARPA：錄取所選回波 AIS：激活所選目標 REF MARK 參考標志 Inscribes reference mark, for target-based speed input. 標繪參考標志，輸入目標基準速度 EBL OFFSET 電子方位線偏心 Offsets EBL, to measure range and bearing between two targets. 電子方位線偏心顯示，測量?jī)晌飿?biāo)之間的方位和距離 OFF CENTER偏心顯示 Shifts screen

51、center to chosen location. 偏心顯示于所選位置 ZOOM變焦放大 Zooms chosen location. 放大顯示所選位置 MARK DELETE 標志刪除 Deletes chosen mark (plotter mark, origin mark or waypoint mark). 刪除標志 CHART ALIGN 海圖排列 Aligns chart with radar picture. 電子海圖與雷達圖像排列 6. The guidance box shows "XX / EXIT." (XX = function

52、chosen). Roll the trackball to place the cursor where desired. 當引導框顯示“xx/退出”時，將鼠標置于所需位置； 7. Push the left button to execute the function selected at step 5. 按左鍵執行所選功能（第5步時所選擇的功能）； 8. To quit the function selected, push the right button when the guidance box shows "XX / EXIT." (XX = function c

53、hosen at step 5) 當引導框顯示“xx/退出”時，按右鍵退出。 1.7 Monitor Brilliance 顯示器亮度 The brilliance of the entire screen should be adjusted according to lighting conditions. Monitor brilliance should be adjusted before adjusting relative brilliance levels on the BRILL menu to be explained later. 整個顯示器的亮度應根

54、據環境照明來決定，顯示器亮度應在調節相對亮度之前調節。 Note: The brilliance of a commercial monitor cannot be adjusted from the radar. See the owners manual of the commercial monitor for how to adjust its brilliance. 不能在雷達中調節商用顯示器的亮度。詳見用戶手冊。 By keyboard 鍵盤操作 Operate the [BRILL] control on the control unit to adjust brilli

55、ance. Turn it clockwise to increase brilliance; counterclockwise to decrease brilliance. Watch the BRILL box (see illustration below) to know current brilliance level. 使用鍵盤上的亮度調節旋鈕調節亮度，順時針增加亮度，逆時針減小亮度，觀察屏幕之亮度調節框。 By trackball 鼠標操作 1、Roll the trackball to place the arrow on the brilliance level in

56、dicator in the brilliance level indication box at the bottom left corner of the screen. 將光標置于屏幕左下角的亮度調節框中的亮度調節條上； 亮度調節框 2. Roll the wheel downward to increase brilliance or roll it upward to decrease brilliance. The length of the brilliance bar increases or decreases with operatio

57、n of the wheel. 向下滾動鼠標增加亮度，向上滾動鼠標降低亮度，調節條上的長短根據滾輪滾動而定； Note: If nothing appears on the screen at power-up when using Control Unit RCU-015 (palm control) or when the radar is in stand-by, press and hold down any key except the power switch for four seconds to automatically set up for medium display

58、 brilliance. 當使用Control Unit RCU-015（掌中遙控）時或待機時，如果在開機的情況下屏幕無任何顯示，按住除電源鍵以外的任何鍵4秒鐘，自動調節顯示器至中等顯示亮度。 1.8 Choosing the Display Mode 選擇顯示模式 This radar has two display modes: Radar and Radar + Plotter. Choose a display mode as below. Note that a display mode cannot be chosen when the menu is open.

59、 本雷達有兩種顯示方式：雷達顯示和雷達標繪顯示。選擇方法如下： 注意：當有菜單打開時，不能選擇顯示方式。 1. Roll the trackball to place the arrow in the DISPLAY MODE box at the top of the screen. 滾動滾輪將光標移屏幕上方的顯示模式選擇框上； 顯示模式選擇框 2. Push the left button to choose appropriate mode: RADAR: Radar picture +PLOTTER:

60、Radar picture + plotter picture (incl. chart) 按左鍵選擇適當?shù)哪Ｊ健? 1.9 On-Screen Boxes and Markers 屏幕功能框及相關標志 1.10 Tuning the Receiver 調諧 1.10.1 Choosing the tuning method 選擇調諧方式 The tuning method can be selected with the TUNE box at the top of the screen. 調諧方式可在屏幕上方的調諧框中選擇 1. Rol

61、l the trackball to choose the TUNE box (TUNE AUTO or TUNE MAN) at the top of the screen. 移動跟蹤球選擇屏幕上方的調諧框； 調諧框 2. Push the left button or roll the wheel to display TUNE AUTO or TUNE MAN as appropriate. 按左鍵或滾動滾輪選擇顯示自動調諧或手動調諧 3. If you used the wheel to choose tuning method, push t

62、he wheel or the left button to change setting. 如用滾輪選擇調諧方式，按左鍵或滾輪確認 1.10.2 Initializing tuning 初始化調諧 Automatic tuning is initialized during the installation. However, if you feel that automatic tuning is not working properly try re-initializing it as follows: 自動調諧已在安裝時完成，如調諧工作不正?？砂慈缦虏襟E調諧： 1.

63、 Roll the trackball to choose the MENU box at the right side of the screen and then push the wheel or the left button. 滾動跟蹤選擇主菜‘并按飛輪或左鍵； 2、 Roll the wheel to choose 1 ECHO and then push the wheel or the left button. 滾動飛輪選擇1回波，并按飛輪或左鍵； [回波] 1 返回 2 二次反射回波抑制 關 /開 3 調諧初始化 4 性能監視器 關 /

64、 開 5 雷達應達器 關 / 開 6 刷刮功能 關 / 開 回波菜單 3. Roll the wheel to choose 3 TUNE INITIALIZE. 滾動飛輪選擇3調諧初始化； 4．Push the wheel or the left button to initialize automatic tuning. (For operation from the keyboard, press the [ENTER MARK] key.) "WORK IN PROGRESS -TUNE INITIALIZE appears in the Aler

65、t Box during the initialization. 按滾輪或左鍵初始化調諧，鍵盤操作請按[ENTER MARK]，初始化過程中警報框顯示“WORK IN PROGRESS -TUNE INITIALIZE“； 5．Push the right button twice to close the menu. 按右鍵退出菜單。 1.10.3 Automatic tuning 自動調諧 Choose automatic tuning following paragraph 1.10.1. The TUNE box shows TUNEAUTO. 按1.10.1節選擇

66、自動調諧，調諧框顯示自動調諧。 1.10.4 Manual tuning 手動調諧 1. Roll the trackball to choose the RANGE box at top left corner and then push the left or right button as appropriate to choose the 48-mile range. Push the left button to lower the range; the right button to raise the range. 滾動跟蹤球選擇量程框鍵量程設為48海里； 2. Choose manual tuning following the procedure in paragraph 1.10.1. 按1.10.1節選擇手動調諧； 3. Roll the trackball to place the arrow on the tuning bar area in the TUNE box. 將鼠標光標置于調諧框的調諧條上； 3、 Roll